15-Degree Round Head Wire Weld Collated Smooth Shank Electro Galvanized Coil Roofing Nails
Coil roofing nail for are used in siding, sheathing, fencing,subfloor, roof decking exterior deck and trim and some other woodworking.

Bluekin mission is to do our best to become the best supplierAnd make good products for the building hardware market.
Galvanized Material - The roll nails are made of galvanized materials and are not easy to rust.
Application - Wire collated nails are used for both new roofs and reroofing, also for attaching waterproof tar paper, roofing felt, metal drip edges, insulation board, cementitious fiber board products and vinyl siding.


E.G. Finish

Hot Dipped Galvanized

Stainless
Bright Finish
Bright fasteners have no coating to protect the steel and are susceptible to corrosion if exposed to high humidity or water. They are not recommended for exterior use or in treated lumber, and only for interior applications where no corrosion protection is needed. Bright fasteners are often used for interior framing, trim and finish applications.
Hot Dip Galvanized (HDG)
Hot dip galvanized fasteners are coated with a layer of Zinc to help protect the steel from corroding. Although hot dip galvanized fasteners will corrode over time as the coating wears, they are generally good for the lifetime of the application. Hot dip galvanized fasteners are generally used for outdoor applications where the fastener is exposed to daily weather conditions such as rain and snow. Areas near the coasts where the salt content in rain water is much higher, should consider Stainless Steel fasteners as salt accelerates the deterioration of the galvanization and will accelerate corrosion.
Electro Galvanized (EG)
Electro Galvanized fasteners have a very thin layer of Zinc that offers some corrosion protection. They are generally used in areas where minimal corrosion protection is needed such as bathrooms, kitchens and other areas that are susceptible to some water or humidity. Roofing nails are electro galvanized because they are generally replaced before the fastener begins to wear and are not exposed to harsh weather conditions if installed properly. Areas near the coasts where salt content in rain water is higher should consider a Hot Dip Galvanized or Stainless Steel fastener.
Stainless Steel (SS)
Stainless steel fasteners offer the best corrosion protection available. The steel may oxidize or rust over time but it will never lose its strength from corrosion. Stainless Steel fasteners can be used for exterior or interior applications and generally come in 304 or 316 stainless steel.
Coil Roofing Nails Shank Type:
Smooth Shank:
Smooth shank nails are the most common and are often used for framing and general construction applications. They offer enough holding power for most everyday use.
Ring Shank:
Ring shank nails offer superior holding power over smooth shank nails because the wood fills in the crevasse of the rings and also provide friction to help prevent the nail from backing out over time. A ring shank nail is often used in softer types of wood where splitting is not an issue.
Screw Shank:
A screw shank nail is generally used in hard woods to prevent the wood from splitting while the fastener is being driven. The fastener spins while being driven (like a screw) which creates a tight groove that makes the fastener less likely to back out.
Annular Thread Shank:
Annular thread is very similar to a ring shank except the rings are externally beveled which presses against the wood or sheet rock to prevent the fastener from backing out.


Shank Type |
|
Head Style | Flat |
Finish | YELLOW, BLUE, RED, BRIGHT, E.G, H.D.G |
Shank Diameter | 2.1mm--4.3mm(0.083''--0.169'') |
Length | 25mm--150mm(1''--6'') |
Coil Angle | 14-16 Degree |
Point Angle | 40-67 degree diamond |
Usage | Building Construction |
Length | Finish | Pcs/Coil | Coil/carton | Carton/Pallet | CNTR QTY PALLETS | CNTY(L) |
3/4" | E.G | 120 | 60 | 48 | 24 | 20' |
1" | E.G | 120 | 60 | 48 | 24 | 20' |
1-1/4" | E.G | 120 | 60 | 48 | 24 | 20' |
1-1/2" | E.G | 120 | 60 | 48 | 24 | 20' |
1-3/4" | E.G | 12 | 60 | 48 | 24 | 20' |
Various Usages: these galvanized nails are suitable for diverse kinds of 15 degree coil siding and fencing nailers, can be applied for various materials, such as lathing and sheathing, saving you time and effort
Proper Dimension to Apply: each nail of these siding nails is measured about 0.12 x 0.75 inches/ 3.05 x 19 mm and about 15 degree in gradient, appropriate and compact for you to use, without taking up too much space, bringing you a nice and satisfying experience
Application Occasions: the coil nail can be applied for many occasions, such as new roofs installation and repairing the roof, and are also ideal for attaching metal drip edges, waterproof tar paper, insulation board and so on

∗ Application on : • Wooden Packaging, Construction of Pallets, Cases and Window Crates. • Window and door frames. • Panel sheathing and fencing.